How
to order Select
your car Place
order
Select
your car
Installation of GAN products

Our engineers have been working for a long time, so that you can easily install the GAN device and easily manage it. Have control over your car’s power capacity! In most cases GAN products are designed for self-installation which takes no more than 15 minutes.

1
Connect your GAN
to the car
2
Choose your car
in your Smartphone
3
Get up to +30 %
more power
GAN GT/GTL Installation
Watch video GAN GT/GTL Installation
16 EASY STEPS
1
Download GAN App from App Store for iOS or from Google Play for Android.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16 EASY STEPS
1
Download and install GAN APP from App Store (for iOS) or Google Play (for Android).
2
Turn off the ignition, remove the key and wait 5 minutes.
3
Open the bonnet and remove the engine cover as shown in the example for Audi А6 1,8Т 190 hp.
4
Locate the sensors that are relevant for the installation in your vehicle. Points of connection are marked by arrows.
5
Remove the plug from the first sensor.
6
Connect the corresponding socket of cable to the first sensor and disconnected plug. Make sure that the plugs are properly fixed. "Click" sound should be heard when you connect the plugs. In this way GAN device will be connected to the first sensor.
7
Remove the plug from the second sensor.
8
Connect the corresponding socket of cable to the second sensor and disconnected plug. Make sure that the plugs are fixed. "Click" sound should be heard when you connect the plugs. In this way GAN device will be connected to the second sensor.
9
Connect GAN GT device to the big plug of the cable.
10
Place GAN GT device and the cable at a suitable point using plastic ties.
11
Fasten the engine cover. Close the bonnet.
12
Start the engine.
13
Connect to your GAN in the application. Use the last 6 digits of the serial number of the device as a password.
14
Choose your car in the application. Then necessary settings will be sent to the device.
15
You can choose between operating modes SPORT, DYNAMIC, ECO, STOCK (OFF) on your Smartphone.
16
Feel your car in a new way!
10 EASY STEPS
1
Download GAN App from App Store for iOS or from Google Play for Android.
1
2
3
4
5
6
7
8
9
10
10 EASY STEPS
1
Download GAN App from App Store for iOS or from Google Play for Android.
2
Warm up your engine to operating temperature (90 C).
3
Find OBD-II connector in your vehicle. Usually it is located under the steering wheel. You can find the exact location of the OBD-II connector in the installation guide for your car.
4
Plug the device into OBD-II connector when the engine is running.
5
Connect to your GAN in the application. Use the last 6 digits of the serial number of the device as a password.
6
Choose your car in the application, and the necessary settings will be sent to the device
7
The calibration begins after settings have been downloaded, and takes 3 minutes. LED is flashing red during calibration and you can check calibration process status on your Smartphone. After the calibration is finished, the device is in the working mode (LED is solid yellow).
8
A 120 km drive is required before the device adapts to the engine control unit.
9
You can choose between operating modes DYNAMIC, ECO, STOCK (OFF) on your Smartphone.
10
Feel your car in a new way!
10 EASY STEPS
1
Download GAN PC App from INSTALLATION section.
1
2
3
4
5
6
7
8
9
10
10 EASY STEPS
1
Download GAN PC App from INSTALLATION section.
2
Connect the device to your PC with a Micro USB cable.
3
Choose your car in the application, and the necessary settings will be sent to the device.
4
GAN is ready for the installation into your vehicle.
5
Warm up your engine to operating temperature (90 C)
6
Find OBD-II connector in your vehicle. Usually it is located under the steering wheel. You can find the exact location of the OBD-II connector in the installation guide for your car.
7
Plug the device into OBD-II connector when the engine is running.
8
The calibration begins after settings have been downloaded, and takes 3 minutes. LED is flashing red during calibration and you can check calibration process status on your Smartphone. After the calibration is finished, the device is in the working mode (LED is solid yellow).
9
A 120 km drive is required before the device adapts to the engine control unit.
10
Feel your car in a new way!
Installation guide download
You can download installation guide in pdf.
Download app for your Smartphone by choosing your operating system
Download GAN PC
Programm GAN DeaktopControl for Windows XP, Vista, 7,8,10


We are using cookies so that your shopping experience gets better. By continuing to browse our website you are accepting USAGE OF COOKIES.

GAN Tuning
X